Castleport Test Prep

CCHT Practice Test: 50 Free Questions With Answers

50 original, unofficial questions. This is not a full-length exam. Pick an answer, then open the explanation.

Practice questions

Question 1 of 50

Clinical · CCHT-001

Inside the dialyzer, dialysate flows in the opposite direction to the blood. What does this countercurrent flow do?

  • A. It keeps the concentration gap high along the fiber, so more waste diffuses out
  • B. It raises pressure on the dialysate side so the blood gives up extra fluid
  • C. It pushes small air bubbles toward the drain before they reach the blood
  • D. It brings the dialysate to body temperature before it touches the fibers
Show answer and explanation

Correct answer: A. NIDDK describes blood moving through hollow fibers while dialysis solution passes the opposite way on the outside. Waste moves from blood into dialysate because of the concentration difference, and running the flows in opposite directions keeps that difference high from one end of the fiber to the other. The Indian hemodialysis guideline makes the same point from the other side: in dialysis disequilibrium, switching dialysate to co-current flow is used on purpose to make solute removal less efficient.

Why the other choices don't fit

  • B: Flow direction is about keeping the solute gradient, not about creating pressure for fluid removal.
  • C: Air protection comes from the air detector and venous drip chamber, not dialysate direction.
  • D: The machine's heater sets temperature regardless of flow direction.

Source: NIDDK (National Institutes of Health), Hemodialysis, "What happens to my blood while it's in the filter?"; Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", "Dialysis Disequilibrium Syndrome"

Question 2 of 50

Technical · CCHT-002

How do the AAMI requirements adopted by CMS say carbon adsorption beds must be set up in a dialysis water system?

  • A. One large bed sized for peak flow, with a port at the outlet
  • B. Two beds in series, with a sample port after each bed
  • C. Two beds in parallel, each feeding a separate RO unit
  • D. One carbon bed placed after the reverse osmosis unit
Show answer and explanation

Correct answer: B. CMS tag V192 (ANSI/AAMI RD52:2004) requires two carbon beds installed in series with a sample port after the first bed, and another after the second for use if chlorine or chloramine breaks through the first. Carbon is the main way to remove free chlorine and chloramine, which cause red cell hemolysis in patients.

Why the other choices don't fit

  • A: A single bed leaves no backup if it is exhausted.
  • C: Series beds are the stated setup, so the second bed backs up the first.
  • D: Carbon sits in pretreatment to protect patients and the RO membrane.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V192

Question 3 of 50

Clinical · CCHT-003

A patient asks what the team means by "dry weight." Which answer is correct?

  • A. Your weight first thing in the morning on a treatment day, before you eat or drink
  • B. Your weight with no extra fluid in your body, which we aim to reach at the end of treatment
  • C. The lowest weight the machine will let us remove fluid down to during a treatment
  • D. Your weight with shoes, jacket and anything in your pockets taken off before treatment
Show answer and explanation

Correct answer: B. NIDDK defines ideal dry weight as your weight when you don't have extra fluid in your body, and says that with sodium control and working dialysis a patient should reach it at the end of every treatment.

Why the other choices don't fit

  • A: Skipping food and drink for one morning doesn't remove fluid built up since the last treatment.
  • C: Dry weight is a clinical target set by the care team, not a machine limit.
  • D: Clothing changes the scale reading, but dry weight is about body fluid.

Source: NIDDK (National Institutes of Health), Hemodialysis, "How will I know if my hemodialysis is working?"

Question 4 of 50

Environment · CCHT-004

Your hands aren't visibly soiled and you're moving to the next patient's station. Which hand hygiene choice fits CMS guidance?

  • A. Wipe gloved hands with a disinfectant wipe, then move on to the next station
  • B. Keep your gloves on and put a fresh pair over them before the next patient
  • C. Rinse hands under running water for a few seconds, then pull on new gloves
  • D. Use an alcohol-based rub with 60 to 90% alcohol and rub all surfaces until dry
Show answer and explanation

Correct answer: D. CMS tag V113 says hand hygiene is soap and water or a waterless alcohol-based rub with 60 to 90% alcohol. Use soap and water if hands are visibly soiled; otherwise the rub is fine, covering all hand surfaces until dry. Gloves come off and hand hygiene is done between each patient or station.

Why the other choices don't fit

  • A: Wiping gloves isn't hand hygiene; gloves are removed between patients.
  • B: Gloves must come off and hand hygiene must be done between patients.
  • C: Water alone isn't hand hygiene.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V113

Question 5 of 50

Role Responsibilities · CCHT-005

Under the CMS Conditions for Coverage, how long after being hired does a new dialysis patient care technician have to become certified (by a state program or a national program such as the CCHT)?

  • A. 90 days
  • B. 6 months
  • C. 18 months
  • D. 5 years
Show answer and explanation

Correct answer: C. CMS tag V695 requires newly employed patient care technicians to be certified under a state or national commercially available program within 18 months of hire. Until certified, they must have completed the facility's approved training program before giving care independently.

Why the other choices don't fit

  • A: Not the CMS time frame.
  • B: Six months is NNCC's recommended (not required) experience before testing.
  • D: Not the CMS time frame.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V695 and V693; NNCC, CCHT certification page, eligibility

Question 6 of 50

Clinical · CCHT-006

A patient's target (dry) weight is 82.0 kg. Today's pre-treatment weight is 84.6 kg with the same clothing as usual. Before any fluids given during treatment are added in per facility protocol, how much weight is above target?

  • A. 1.6 kg
  • B. 2.4 kg
  • C. 2.6 kg
  • D. 3.6 kg
Show answer and explanation

Correct answer: C. 84.6 − 82.0 = 2.6 kg above target. The pre-dialysis check in the Indian guideline lists recording weight and confirming dry weight to plan the ultrafiltration (UF) target. Your facility's protocol then says how to account for saline, rinseback or anything the patient takes in during the run.

Why the other choices don't fit

  • A: This would mean a pre-weight of 83.6 kg.
  • B: This would mean a pre-weight of 84.4 kg.
  • D: This adds a kilogram that isn't there.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Priming, Connecting and Disconnecting", patient assessment before dialysis; NIDDK (National Institutes of Health), Hemodialysis, "dry weight"

Question 7 of 50

Technical · CCHT-007

Your unit runs set patient shifts. When should total chlorine (or chloramine) be tested after the carbon tanks, per CMS guidance?

  • A. At the start of each treatment day before patients start, and again before each shift
  • B. Once each week, on the same day the water softener is checked and regenerated
  • C. Only when the reverse osmosis unit alarms for low rejection or poor water quality
  • D. Once each month, at the same time bacterial cultures and endotoxin samples are drawn
Show answer and explanation

Correct answer: A. CMS tag V196 says testing should be done at the beginning of each treatment day before patients start treatment and again before each patient shift. Without set shifts, test about every 4 hours. Results are recorded on a log.

Why the other choices don't fit

  • B: Weekly testing is far too infrequent, since chloramine levels can change day to day.
  • C: An RO alarm doesn't tell you chloramine is getting through the carbon.
  • D: Cultures and endotoxin are separate tests on a different schedule.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V196

Question 8 of 50

Clinical · CCHT-008

Which set of checks does the Indian hemodialysis guideline list for the patient assessment before dialysis starts?

  • A. Hemoglobin, ferritin and a potassium level drawn before every single treatment
  • B. Last treatment's blood flow rate, dialyzer size and how long the run lasted
  • C. Weight, lying and standing BP, any new symptoms, and the dry weight to plan the UF goal
  • D. A chest X-ray and a 12-lead ECG to look for heart and lung changes
Show answer and explanation

Correct answer: C. The guideline's pre-dialysis assessment is: record weight, measure blood pressure lying and standing, ask about new symptoms, and confirm dry weight to plan the target UF.

Why the other choices don't fit

  • A: Anemia labs are monitored monthly under the CMS measures tool, not before every run.
  • B: Last treatment's settings don't tell you about today's patient.
  • D: These are not routine pre-treatment checks.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Priming, Connecting and Disconnecting", patient assessment before dialysis; CMS, ESRD Interpretive Guidance v1.1, Measures Assessment Tool (MAT), V548 (monthly Hgb)

Question 9 of 50

Clinical · CCHT-009

You place your fingers over a healthy, mature AV fistula. What should you normally feel?

  • A. No movement at all
  • B. A continuous vibration (thrill)
  • C. Coolness compared with the other arm
  • D. A strong water-hammer pulse with no vibration
Show answer and explanation

Correct answer: B. NIDDK tells patients that a working access has a vibration you can feel and to report it if the vibration is gone. The Indian guideline's access exam lists a continuous thrill and the absence of a water-hammer pulse as normal findings.

Why the other choices don't fit

  • A: No vibration can mean poor flow or a blockage; NIDDK says to tell the dialysis center if you cannot feel it.
  • C: Coldness is an abnormal finding on palpation.
  • D: A water-hammer pulse is listed as abnormal, a sign of outflow narrowing.

Source: NIDDK (National Institutes of Health), Hemodialysis, "Take care of your access"; Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Vascular Access", "Examination of an arteriovenous fistula"

Question 10 of 50

Technical · CCHT-010

Your unit tests for total chlorine (free chlorine plus chloramine together) instead of measuring each one separately. Under the AAMI text CMS adopted at tag V196, what is the maximum allowed in water leaving the first carbon bed?

  • A. Below 0.5 mg/L
  • B. Below 0.1 mg/L
  • C. Below 2.0 mg/L
  • D. Below 1.0 mg/L
Show answer and explanation

Correct answer: B. CMS tag V196 says sampling for total chlorine, allowing a maximum of less than 0.1 mg/L, is often simpler than analyzing free chlorine and chloramine separately. A total chlorine test can't tell the two apart, so the stricter chloramine limit (0.1 mg/L) applies to the whole reading. Test kits must be sensitive enough to resolve that level.

Why the other choices don't fit

  • A: 0.5 mg/L is the maximum for free chlorine when it is measured on its own (tag V192), not for a total chlorine reading.
  • C: Above the limit.
  • D: Above the limit.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V196 and V192

Question 11 of 50

Environment · CCHT-011

You took a pack of alcohol swabs and an unopened syringe to a patient's station but didn't use them. What should happen to them?

  • A. Return them to the clean supply cart, since the packages were never opened
  • B. Hand them to the next patient you set up, since they are still sealed and sterile
  • C. Use them only for that patient and don't return them to the shared clean supply
  • D. Wipe the outside of each package with disinfectant, then put them back in stock
Show answer and explanation

Correct answer: C. CMS tag V116 says unused medications and supplies (syringes, alcohol swabs and so on) taken to a patient's station should be used only for that patient and not returned to a common clean area or used on other patients. Anything taken to the station may be contaminated with blood.

Why the other choices don't fit

  • A: Unopened or not, items taken to a station can be contaminated and can't go back to the clean supply.
  • B: Using them on another patient is exactly what CMS prohibits.
  • D: Wiping the package doesn't make returning it acceptable under V116.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V116

Question 12 of 50

Clinical · CCHT-012

While listening along a patient's fistula, you hear a high-pitched sound only during systole instead of the usual low, continuous whoosh. What does this most likely suggest?

  • A. A normal, well-developed fistula
  • B. A narrowing (stenosis) in the access
  • C. Too much heparin
  • D. An infection at the needle site
Show answer and explanation

Correct answer: B. The Indian guideline says auscultation should reveal a continuous low-pitched bruit, and that stenosis is revealed by a high-pitched systolic bruit. Report it so the access can be evaluated.

Why the other choices don't fit

  • A: A normal fistula has a continuous low-pitched bruit.
  • C: Bruit pitch doesn't measure anticoagulation.
  • D: Infection shows as redness, discharge or swelling, not a change in bruit.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Vascular Access", "Examination of an arteriovenous fistula"

Question 13 of 50

Role Responsibilities · CCHT-013

Which subject does CMS require in a patient care technician training program?

  • A. Insurance billing codes
  • B. Prescribing medications
  • C. Water treatment and dialysate preparation
  • D. Performing surgery to create access
Show answer and explanation

Correct answer: C. CMS tag V694 lists the required training subjects: principles of dialysis; care of patients with kidney failure, including interpersonal skills; dialysis procedures and documentation (initiation, cannulation, monitoring and termination); possible complications; water treatment and dialysate preparation; infection control; safety; and dialyzer reprocessing if applicable.

Why the other choices don't fit

  • A: Not a required training subject.
  • B: Technicians don't prescribe.
  • D: Access surgery is done by surgeons or interventional physicians.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V694

Question 14 of 50

Clinical · CCHT-014

Which vascular access does NIDDK call the best long-term option for hemodialysis?

  • A. Temporary femoral catheter
  • B. AV graft
  • C. Tunneled central venous catheter
  • D. AV fistula
Show answer and explanation

Correct answer: D. NIDDK calls the AV fistula the best long-term access because it gives the highest blood flow, is less likely to become infected or clot, and lasts longer. The CMS measures tool lists the fistula as preferred, a graft as acceptable if a fistula isn't possible, and catheters to be avoided except in specific situations.

Why the other choices don't fit

  • A: NIDDK describes catheters as temporary access.
  • B: A graft can be used sooner but has more infection and clotting problems.
  • C: CMS lists catheters as access to avoid unless they bridge to a fistula, graft or PD, or in special cases.

Source: NIDDK (National Institutes of Health), Hemodialysis, "Vascular access surgery"; CMS, ESRD Interpretive Guidance v1.1, Measures Assessment Tool (MAT), V550–V551

Question 15 of 50

Technical · CCHT-015

The sample after the first carbon bed tests positive for chloramine, but the sample after the second bed is negative. What does CMS guidance allow?

  • A. Bypass both carbon beds for now and rely on the reverse osmosis unit to remove chloramine
  • B. Keep operating with no time limit, because the second bed is still removing chloramine
  • C. Keep operating for up to 72 hours until a new bed is in, if the second port stays negative
  • D. Backwash the first bed to regenerate the carbon, then put it back into normal service
Show answer and explanation

Correct answer: C. CMS tag V197 allows operation for up to 72 hours while a replacement bed is installed, if the second port stays negative. The new bed goes in the second position and the old second bed moves to first. Logs during this time should show actual testing times.

Why the other choices don't fit

  • A: Carbon is the required chloramine barrier; bypassing it removes patient protection.
  • B: The second bed is now the only protection and its capacity is unpredictable, so the time limit applies.
  • D: CMS notes backwashing does not regenerate carbon.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V197 and V196 (AAMI rationale)

Question 16 of 50

Clinical · CCHT-016

A patient with advancing kidney disease who has not started dialysis needs a lab draw. Following NIDDK's advice for protecting future access sites, where should the draw be done?

  • A. A vein below the wrist, such as on the back of the hand
  • B. Whichever arm vein is easiest to see
  • C. Always the inside of the elbow on the non-dominant arm
  • D. Any vein, because only fistula surgery affects the veins
Show answer and explanation

Correct answer: A. NIDDK tells people with kidney disease to remind providers to draw blood and insert IVs only in veins below the wrist, such as the back of the hand, because damaged arm veins may not be usable for dialysis access later.

Why the other choices don't fit

  • B: Ease of access is what leads to damage of veins needed for a future fistula.
  • C: The inner elbow is one of the arm veins NIDDK asks to protect.
  • D: Repeated draws and IVs can damage veins.

Source: NIDDK (National Institutes of Health), Hemodialysis, "Take care of the blood vessels in your arms"

Question 17 of 50

Clinical · CCHT-017

When cannulating an AV fistula with two needles, how does the Indian guideline describe needle placement?

  • A. Venous needle nearer the anastomosis; arterial needle further up the arm, aimed toward the hand
  • B. Arterial needle in the artery above the anastomosis; venous needle in the fistula vein
  • C. Both needles side by side at the same spot so they share a single, well-healed site
  • D. Arterial needle nearer the anastomosis; venous needle further downstream, aimed toward the heart
Show answer and explanation

Correct answer: D. The guideline places both needles in the vein downstream of the anastomosis, with the arterial needle more distal (it is inserted about 3 cm from the anastomosis) and the venous needle pointing downstream, usually toward the heart, at least 3 to 5 cm beyond the arterial needle to minimize recirculation.

Why the other choices don't fit

  • A: Reversing positions sends cleaned blood back into the arterial needle (recirculation).
  • B: Both needles go in the arterialized vein, not the artery.
  • C: Needles too close together increase recirculation.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Priming, Connecting and Disconnecting", "procedure for handling AVF or/graft"

Question 18 of 50

Environment · CCHT-018

What does CMS guidance say about delivering medications to patients in the treatment area?

  • A. Load a shared medication cart and wheel it from station to station during the shift
  • B. Draw up medications at the patient's chair so the label can be checked at the bedside
  • C. Carry the multiple-dose vial from chair to chair and draw up each dose at the station
  • D. Prepare each dose in a clean area away from stations and bring it to each patient separately
Show answer and explanation

Correct answer: D. CMS tag V117 requires clean areas for preparing medications, separate from areas where used equipment or blood samples are handled. Individual doses are prepared centrally and delivered separately to each patient. Common medication carts must not be used, and multiple-dose vials are not carried between stations.

Why the other choices don't fit

  • A: CMS says common medication carts must not be used.
  • B: Patient stations are not clean preparation areas.
  • C: CMS says not to carry multiple-dose vials from station to station.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V117

Question 19 of 50

Technical · CCHT-019

When you draw a sample to test for chloramine after the carbon beds, which practice does CMS guidance describe?

  • A. Collect it in the afternoon and run the test first thing the next morning instead
  • B. Draw it after the system has run at least 15 minutes and test it on site right away
  • C. Draw it right after a long shutdown, before water has started moving through the beds
  • D. Send it to an outside lab so a certified technician can run it within a few days
Show answer and explanation

Correct answer: B. CMS tag V196 says samples should be drawn when the system has been running at least 15 minutes, and analyzed on site because chloramine levels drop if the sample isn't tested promptly.

Why the other choices don't fit

  • A: Holding the sample overnight has the same problem.
  • C: Water that sat in the bed during a shutdown can give a misleading result.
  • D: Delayed testing lets chloramine decrease, giving a false low.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V196

Question 20 of 50

Clinical · CCHT-020

Once a buttonhole tunnel track has formed in a fistula, which needle does the Indian guideline say to use?

  • A. A sharp needle every time
  • B. A larger sharp needle to keep the track open
  • C. Whatever needle is in stock
  • D. A dull (blunt) bevel needle
Show answer and explanation

Correct answer: D. The guideline says that after about 6 to 10 sharp-needle cannulations form a scar-lined track, only dull bevel needles should be used to protect the vessel wall. It recommends buttonhole cannulation only where blunt needles are available, and the stepladder (railroading) technique otherwise.

Why the other choices don't fit

  • A: Sharp needles in an established track can cut the tunnel and damage the vessel wall.
  • B: Larger sharp needles would cause more damage.
  • C: Needle choice for buttonholes is specific, not whatever is available.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Priming, Connecting and Disconnecting", buttonhole procedures

Question 21 of 50

Role Responsibilities · CCHT-021

Per CMS guidance on emergency preparedness, which certification must all direct patient care staff (nurses and patient care technicians) keep current?

  • A. Phlebotomy certification
  • B. Advanced cardiac life support
  • C. Basic CPR
  • D. Water treatment certification
Show answer and explanation

Correct answer: C. CMS tag V410 says all direct patient care staff, nurses and patient care technicians, must have current basic CPR certification.

Why the other choices don't fit

  • A: Not the V410 requirement.
  • B: CMS states basic CPR as the requirement for all direct care staff.
  • D: Not the V410 requirement.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V410

Question 22 of 50

Clinical · CCHT-022

You've cleaned a patient's fistula arm, applied the skin antiseptic and let it dry. Before inserting the needle, you want to feel the vein again. Based on CDC's cannulation audit tool, what should happen?

  • A. Don't touch the site after antisepsis; if you must feel it again, redo the skin prep
  • B. Feel the vein, then wipe the spot once with dry sterile gauze before cannulating
  • C. Feel the vein with the same gloves, since the antiseptic on the skin is still working
  • D. Blow gently on the site so it dries faster, then feel the vein one more time
Show answer and explanation

Correct answer: A. CDC's AV fistula/graft cannulation audit checks that the site is washed, hand hygiene is done, new clean gloves are worn, antiseptic is applied and allowed to dry, and there is no contact with the site after antisepsis before aseptic cannulation. Touching it again recontaminates the skin, so the prep has to be redone.

Why the other choices don't fit

  • B: Dry gauze doesn't disinfect skin.
  • C: Touching the prepared site is exactly what the audit tool marks as a failure.
  • D: Blowing on the site adds contamination and still involves touching it.

Source: CDC, Audit Tool: Arteriovenous fistula/graft cannulation observations (PDF), cannulation observation columns

Question 23 of 50

Technical · CCHT-023

What minimum total empty bed contact time (EBCT) does CMS guidance require for granular activated carbon at the maximum product water flow?

  • A. 2 minutes total
  • B. 5 minutes total
  • C. 10 minutes total
  • D. 30 minutes total
Show answer and explanation

Correct answer: C. CMS tag V195 requires each adsorption bed to have an EBCT of at least 5 minutes at maximum product water flow, for a total of at least 10 minutes. Added shifts or treatments mean more water demand, which may require more carbon.

Why the other choices don't fit

  • A: Too short.
  • B: 5 minutes is the per-bed minimum, not the total.
  • D: Longer than the stated minimum; CMS sets 10 minutes total.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V195

Question 24 of 50

Clinical · CCHT-024

Before removing the cap from a hemodialysis catheter limb, what does CDC's Scrub-the-Hub protocol say to do first (after hand hygiene and new clean gloves)?

  • A. Clamp the catheter
  • B. Flush the line with saline
  • C. Attach the blood line
  • D. Unclamp the catheter so blood can flow
Show answer and explanation

Correct answer: A. CDC's protocol: always clamp the catheter before removing the cap, and never leave an uncapped catheter unattended. Hubs stay open for the shortest time possible.

Why the other choices don't fit

  • B: Flushing comes after the hub is disinfected and a sterile syringe is attached.
  • C: Blood lines connect only after hub disinfection and the withdraw-and-flush step.
  • D: An unclamped, uncapped limb can let air in or blood out.

Source: CDC, Hemodialysis Central Venous Catheter Scrub-the-Hub Protocol (PDF), Connection Steps 1–2

Question 25 of 50

Clinical · CCHT-025

You're disinfecting both hubs of a dialysis catheter. Which practice matches CDC's Scrub-the-Hub protocol?

  • A. Wipe only the open end of each hub quickly, since the threads never touch the blood
  • B. Soak both caps in antiseptic for several minutes in place of scrubbing the hubs
  • C. Use a new pad for each hub, scrub its threads and end with friction, and let it dry
  • D. Use one pad for both hubs, scrubbing the first hub's end and then the second hub's end
Show answer and explanation

Correct answer: C. CDC says to use a new antiseptic pad for each hub, scrub the sides (threads) and end thoroughly with friction to remove residue such as blood, and hold the limb while the antiseptic dries. The protocol notes that cap soaking is not a CDC/HICPAC recommendation.

Why the other choices don't fit

  • A: CDC says to scrub the threads as well as the end.
  • B: CDC says the role of soaking caps isn't clear and doesn't recommend it.
  • D: Sharing one pad can carry contamination from one hub to the other.

Source: CDC, Hemodialysis Central Venous Catheter Scrub-the-Hub Protocol (PDF), Connection Step 3 and "Soaking Caps"

Question 26 of 50

Environment · CCHT-026

A venous transducer protector gets wet with blood during treatment. What does CMS guidance say to do?

  • A. Let it air-dry at the end of the shift and reuse it on the next patient on that machine
  • B. Leave it in place until the treatment ends, then replace it before the next patient
  • C. Dry it off with sterile gauze, check that the pressure reading is back, and reconnect
  • D. Replace it right away; if fluid shows on the machine side, have the machine checked after treatment
Show answer and explanation

Correct answer: D. CMS tag V120 says a wet external transducer protector must be replaced immediately and inspected. If fluid is visible on the machine side, qualified staff must open the machine after treatment to check the internal transducer and tubing. A contaminated machine is taken out of service and disinfected. Protectors are changed for each treatment and never reused.

Why the other choices don't fit

  • A: Protectors are not reused.
  • B: A wet protector must be changed immediately.
  • C: Drying doesn't restore the barrier.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V120

Question 27 of 50

Clinical · CCHT-027

What does CDC list as the first-line skin antiseptic for catheter dressing changes in dialysis, for patients who can tolerate it?

  • A. Chlorhexidine (over 0.5%) in alcohol
  • B. Plain soap and warm water
  • C. Hydrogen peroxide (3%) solution
  • D. Sterile normal saline (0.9%)
Show answer and explanation

Correct answer: A. CDC's Core Interventions call for an alcohol-based chlorhexidine (>0.5%) solution as the first-line skin antiseptic for central line insertion and dressing changes, with povidone-iodine (preferably with alcohol) or 70% alcohol as alternatives for chlorhexidine intolerance.

Why the other choices don't fit

  • B: Soap and water cleans but isn't the antiseptic CDC lists.
  • C: Hydrogen peroxide isn't one of CDC's listed options.
  • D: Saline has no antiseptic action.

Source: CDC, Best Practices for Bloodstream Infection Prevention in Dialysis Settings (Core Interventions), "Chlorhexidine for skin antisepsis"

Question 28 of 50

Technical · CCHT-028

The carbon in a tank needs replacing. What does CMS guidance require for the replacement media?

  • A. The existing carbon, as long as it has been backwashed thoroughly first
  • B. New (virgin) granular activated carbon with an iodine number of 900 or higher
  • C. Regenerated carbon from a vendor, since it costs less and works the same way
  • D. Carbon moved over from the second tank, with nothing new added to the system
Show answer and explanation

Correct answer: B. CMS tag V194 says granular activated carbon with a minimum iodine number of 900 must be specified when ordering. The AAMI rationale in V196 says a new bed of virgin carbon is used for replacement, carbon cannot be regenerated at a dialysis facility, and regenerated carbon is prohibited.

Why the other choices don't fit

  • A: Backwashing doesn't regenerate carbon.
  • C: Regenerated carbon is prohibited.
  • D: Moving the second bed forward is part of rotation, but the new bed must be virgin carbon.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V194 and V196 (AAMI rationale)

Question 29 of 50

Clinical · CCHT-029

An hour into treatment, a patient starts yawning, says they feel dizzy, and their blood pressure has dropped well below their baseline. What does the Indian guideline list as the immediate steps?

  • A. Turn the blood pump down to zero and wait for the patient's pressure to come back
  • B. Raise the UF rate so the treatment finishes sooner, before the pressure drops further
  • C. Sit the patient upright, give a glass of water and recheck blood pressure in an hour
  • D. Stop UF, lower the head (Trendelenburg) and give a small saline bolus per protocol
Show answer and explanation

Correct answer: D. For intradialytic hypotension, the guideline's immediate steps are to stop UF, place the patient head-down, give a 100–200 mL bolus of isotonic saline, not reduce the blood flow rate, and reassess blood pressure after 10 minutes. In practice you follow your facility's standing orders and notify the nurse.

Why the other choices don't fit

  • A: The guideline specifically says not to reduce blood flow rate for this.
  • B: More fluid removal makes hypotension worse.
  • C: The guideline's first steps are head-down positioning and IV saline, not sitting up or drinking water.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", "Intradialytic Hypotension" management

Question 30 of 50

Role Responsibilities · CCHT-030

A patient tells you they want to complain about how they were treated but are afraid it will affect their care. Which statement matches the patient rights in CMS guidance?

  • A. They can file with the facility, ESRD Network or state agency, even anonymously
  • B. Only signed, written complaints are accepted, so they'll need to put their name on it
  • C. They can file a grievance only after they transfer to another dialysis facility
  • D. They must first raise it with the technician involved before anyone else can review it
Show answer and explanation

Correct answer: A. CMS tags V465 to V467 say patients must be told about the internal grievance process and external options, including the ESRD Network and State survey agency, and that they can file personally, anonymously or through a representative without reprisal or denial of services.

Why the other choices don't fit

  • B: Anonymous grievances are allowed.
  • C: Patients can file while in care, without fear of reprisal.
  • D: Patients aren't required to go through the staff member involved.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V465–V467

Question 31 of 50

Clinical · CCHT-031

Which combination does the Indian guideline name among the most important factors that set up muscle cramps during dialysis?

  • A. Hypotension, low blood volume, a high UF rate and low-sodium dialysate
  • B. High-sodium dialysate, a low UF rate and a short treatment time
  • C. High blood flow, a brand-new dialyzer and a long treatment time
  • D. Eating before treatment, drinking coffee and a cool treatment room
Show answer and explanation

Correct answer: A. The guideline names four main predisposing factors for intradialytic cramps: intradialytic hypotension, hypovolemia, a high UF rate and low-sodium dialysis solution. First steps are to reduce or stop UF and give saline per protocol.

Why the other choices don't fit

  • B: These are the opposite of the listed UF and sodium factors.
  • C: These aren't among the factors the guideline lists for cramps.
  • D: These aren't listed cramp factors.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", "Intra-dialytic Muscle Cramps"

Question 32 of 50

Technical · CCHT-032

Before each treatment, which dialysate check does CMS guidance require with an independent method, and why?

  • A. pH, and conductivity if the maker requires it, since a concentrate mix-up can harm patients
  • B. No extra check, because the machine's self-test already confirms the dialysate
  • C. Dialysate temperature by touch, since fluid that is too warm can cause hemolysis
  • D. Dialysate color, since the wrong concentrate turns the fluid cloudy or yellow
Show answer and explanation

Correct answer: A. CMS tag V250 says each machine must be tested for pH with a hand-held meter or adequately sensitive strips before every treatment and whenever a different acid concentrate is used, and conductivity must be checked with an independent device if the manufacturer requires it. One concentrate is acidic and the other basic, so connecting the wrong one can harm patients. Some mix-ups give acceptable conductivity with a very low pH, which is why pH matters too.

Why the other choices don't fit

  • B: CMS requires the independent check in addition to the machine reading.
  • C: Touch isn't an independent measurement, and temperature isn't the V250 check.
  • D: Color isn't the check CMS describes; V250 calls for a pH measurement with an independent device.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V250

Question 33 of 50

Environment · CCHT-033

There's visible blood on a dialysis chair after treatment. Which cleanup matches CMS guidance?

  • A. Seat the next patient on a clean pad and clean around them during their treatment
  • B. Wipe it once with a low-level detergent disinfectant, the same as any other surface
  • C. Clean it now with a tuberculocidal or 1:100 bleach solution, then repeat with a new cloth
  • D. Cover it with a towel and clean all the chairs together after the last shift
Show answer and explanation

Correct answer: C. CMS tag V122 says visible blood requires the intermediate-level protocol: clean immediately with a tuberculocidal disinfectant or 1:100 bleach (300 to 600 mg/L free chlorine) for the labeled contact time, place the cloth in a leak-proof container, then apply disinfectant again with a new cloth. No patient should be at the station during this.

Why the other choices don't fit

  • A: No patient should be at the station during the cleanup.
  • B: Low-level disinfection is for surfaces without visible blood.
  • D: Blood must be cleaned up immediately, and stations are disinfected between patients.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V122

Question 34 of 50

Clinical · CCHT-034

You see foam in the venous line and the patient suddenly becomes short of breath. You suspect an air embolism. What should you do immediately?

  • A. Clamp the venous line, stop the pump, and turn the patient onto the left side, head down
  • B. Turn up the blood pump speed so the bubbles clear the venous line more quickly
  • C. Disconnect the arterial needle and let the blood line drain into the prime bucket
  • D. Raise the head of the chair, give oxygen and keep dialyzing while you watch the line
Show answer and explanation

Correct answer: A. The Indian guideline says to immediately clamp the venous blood line, stop the blood pump, tilt the patient to the left side with head and chest facing down, and get medical support with 100% oxygen. It also says the air detector self-test should never be skipped and the detector never disarmed.

Why the other choices don't fit

  • B: Speeding the pump sends air into the patient faster.
  • C: An open line can let more air in.
  • D: Continuing treatment can push more air into the patient.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", "Air Embolism"

Question 35 of 50

Clinical · CCHT-035

The blood in the venous line suddenly looks dark, like port wine, and the patient reports back pain and chest tightness. What does the Indian guideline say about the blood in the circuit?

  • A. Slow the blood pump and continue the treatment while you monitor the patient
  • B. Stop and clamp the lines; don't return it, since hemolyzed blood is very high in potassium
  • C. Give an extra heparin bolus into the circuit to keep the blood from clotting
  • D. Return the blood quickly with saline so the patient doesn't lose that volume
Show answer and explanation

Correct answer: B. Port-wine blood in the venous line is a sign of acute hemolysis. The guideline says to stop and clamp the blood lines immediately and not reinfuse, since hemolyzed blood has very high potassium. Causes include kinked lines and dialysate that is too warm, hypotonic or contaminated (for example with chloramine or bleach).

Why the other choices don't fit

  • A: Continuing exposes the patient to more of the cause.
  • C: Heparin doesn't treat hemolysis.
  • D: Returning hemolyzed blood risks dangerous hyperkalemia.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", "Hemolysis"

Question 36 of 50

Technical · CCHT-036

What action level and maximum does CMS's measures tool list for bacteria in product water and dialysate?

  • A. Action at 1 CFU/mL; maximum below 2 CFU/mL
  • B. No bacteria limit applies if endotoxin is low
  • C. Action at 200 CFU/mL; maximum below 500 CFU/mL
  • D. Action at 50 CFU/mL; maximum below 200 CFU/mL
Show answer and explanation

Correct answer: D. The CMS measures tool lists bacteria in product water and dialysate at an action level of 50 CFU/mL with a maximum below 200 CFU/mL. For endotoxin, the action level is 1 EU/mL and the maximum is below 2 EU/mL.

Why the other choices don't fit

  • A: These numbers mirror the endotoxin limits (EU/mL), not bacteria.
  • B: Both bacteria and endotoxin have limits.
  • C: 200 CFU/mL is the maximum, not the action level.

Source: CMS, ESRD Interpretive Guidance v1.1, Measures Assessment Tool (MAT), V178 and V180; Medical Education Institute, Core Curriculum for the Dialysis Technician, 6th ed., "Dialyzer Reprocessing" module (free PDF), water quality notes

Question 37 of 50

Clinical · CCHT-037

When is dialysis disequilibrium syndrome most likely to occur?

  • A. Mainly in patients with AV grafts, because grafts carry higher blood flow
  • B. In a patient's first few sessions, when blood urea is lowered quickly
  • C. Mainly during home peritoneal dialysis, not in-center hemodialysis
  • D. After many years on dialysis, as the fistula and blood vessels age
Show answer and explanation

Correct answer: B. The guideline says dialysis disequilibrium most often occurs in the first few dialysis sessions if blood urea is reduced rapidly, especially with severe uremia. Signs range from nausea, headache and restlessness to seizures. Prevention is keeping efficiency low in the first sessions.

Why the other choices don't fit

  • A: Access type isn't the risk factor.
  • C: The guideline discusses it in hemodialysis.
  • D: It's linked to early, aggressive treatment, not years on dialysis.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", "Dialysis Disequilibrium Syndrome"

Question 38 of 50

Role Responsibilities · CCHT-038

Several patients on the same shift develop fever and chills during treatment. Under CMS guidance, what must the facility do when this kind of reaction happens?

  • A. Give everyone acetaminophen per standing orders and finish the treatments as usual
  • B. Get blood and dialysate cultures and endotoxin levels, check the water system, then fix the cause
  • C. Switch to a different brand of dialyzer for those patients and take no other action
  • D. Wait and see whether patients on another shift develop the same symptoms first
Show answer and explanation

Correct answer: B. CMS tag V275 requires active surveillance for reactions. When indicated, the facility must obtain blood and dialysate cultures and endotoxin levels, evaluate the water purification system and take corrective action. Nurses and technicians must recognize symptoms that may point to water or dialysate problems and report them.

Why the other choices don't fit

  • A: Treating symptoms alone misses a possible water or dialysate problem.
  • C: The required response starts with cultures, endotoxin testing and water system evaluation.
  • D: Waiting exposes more patients.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V275

Question 39 of 50

Clinical · CCHT-039

A patient wants to pull a blanket up over the access arm and line connections during treatment because they're cold. What does CMS guidance say?

  • A. Video monitoring of the station can stand in for direct staff view
  • B. Only the patient's face has to stay visible, so the arm can be covered
  • C. Face, access site and line connections must stay in staff view all treatment
  • D. A blanket over the access is fine if the venous pressure alarm is set
Show answer and explanation

Correct answer: C. CMS tag V407 requires patients to be in view of staff during hemodialysis; each patient's face, vascular access site and bloodline connections must be visible throughout treatment, and video surveillance does not meet this. Covering the access lets a needle dislodgement or disconnection go unnoticed, which can cause fatal blood loss within minutes.

Why the other choices don't fit

  • A: CMS says video surveillance does not meet the requirement.
  • B: The access and connections must be visible too.
  • D: CMS doesn't make an exception for alarms.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V407

Question 40 of 50

Environment · CCHT-040

You're assigned to a patient who is HBsAg-positive. Which other patient could you care for at the same time, per CMS guidance?

  • A. A patient who is due for a hepatitis B booster
  • B. A patient who is immune to hepatitis B
  • C. A patient who is hepatitis B susceptible
  • D. Any patient, as long as you change gloves
Show answer and explanation

Correct answer: B. CMS tag V131 says one staff member may care for HBV-positive patients and immune patients at the same time, but not for hepatitis B susceptible patients. Patients who need a booster dose should not be assigned to staff caring for HBV-positive patients. CMS also notes HBV can survive on surfaces for at least a week.

Why the other choices don't fit

  • A: CMS specifically excludes patients needing a booster.
  • C: Susceptible patients can't be cared for at the same time.
  • D: Glove changes don't make a susceptible assignment acceptable.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V131 and V128

Question 41 of 50

Technical · CCHT-041

During a treatment, a blood-side alarm triggers (for example, the air detector). What does the Indian machine guideline say the machine should do automatically?

  • A. Keep the treatment running and log the alarm for the nurse to review later
  • B. Stop the blood pump, clamp the venous return line and stop ultrafiltration
  • C. Speed up the blood pump briefly to push the problem through the circuit
  • D. Put dialysate in bypass but keep the blood pump and UF running normally
Show answer and explanation

Correct answer: B. The guideline says all blood alarms (air detector, arterial and venous monitors, blood leak, transmembrane pressure and pump torque) should automatically shut off the blood pump, clamp the venous return line and stop UF, isolating the patient. Then you find and fix the cause per procedure.

Why the other choices don't fit

  • A: A blood alarm is meant to stop the circuit, not only log the event.
  • C: Speeding up could push air or blood loss faster.
  • D: Bypass affects dialysate flow, but blood alarms stop the blood pump and UF.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Selection and Use of Machine, Dialyzer and Dialysis Fluid", blood alarms

Question 42 of 50

Clinical · CCHT-042

A patient's pre-dialysis BUN is 75 mg/dL and post-dialysis BUN is 24 mg/dL. What is the urea reduction ratio (URR), and does it meet the URR goal in the CMS measures tool?

  • A. 32%, which does not meet the goal
  • B. 51%, which does not meet the goal
  • C. 68%, which meets the 65% goal
  • D. 68%, which does not meet the 70% goal
Show answer and explanation

Correct answer: C. URR is the percentage drop in urea over the treatment: (75 − 24) ÷ 75 = 51 ÷ 75 = 0.68, or 68%. The CMS measures tool tracks adult hemodialysis adequacy as spKt/V ≥1.2 or URR ≥65%.

Why the other choices don't fit

  • A: 32% is the post-to-pre fraction (24 ÷ 75), not the reduction.
  • B: 51 is the drop in mg/dL, not a percentage.
  • D: The CMS measures tool lists 65%, not 70%.

Source: CMS, ESRD Interpretive Guidance v1.1, Measures Assessment Tool (MAT), V629 (HD adequacy); Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Dialysis Dose and Adequacy", URR target

Question 43 of 50

Clinical · CCHT-043

For the post-dialysis BUN sample, which method does the Indian adequacy guideline describe?

  • A. Slow the blood pump to 100 mL/min and draw the sample about 15 seconds later
  • B. Collect a sample of spent dialysate from the drain line at the end of treatment
  • C. Draw it from the venous line at full blood flow just before the pump stops
  • D. Draw it about 2 hours after treatment ends, once the patient is ready to leave
Show answer and explanation

Correct answer: A. The guideline says the post-dialysis sample should be taken 2 minutes after dialysis, or by slowing the pump to 100 mL/min and drawing 15 seconds later. Your facility's procedure governs the exact method, and sampling errors are one cause the guideline lists for a falsely low Kt/V or URR.

Why the other choices don't fit

  • B: Dialysate isn't a blood sample.
  • C: Blood in the venous line has just been dialyzed and doesn't represent the patient.
  • D: Urea rebounds after treatment, so a late sample isn't the post-dialysis value.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Dialysis Dose and Adequacy", post-dialysis sampling and causes of low Kt/V or URR

Question 44 of 50

Technical · CCHT-044

Under the reuse rules CMS adopted, what happens to a reprocessed hollow-fiber dialyzer whose total cell volume (TCV) falls below 80% of its original value?

  • A. It should be used for a smaller patient
  • B. It is reprocessed again with extra germicide
  • C. It can be used for one more treatment
  • D. It must be discarded
Show answer and explanation

Correct answer: D. The CMS measures tool lists the original TCV as the baseline and says to discard the dialyzer if TCV falls below 80% after reuse. MEI explains that for most hollow-fiber dialyzers a 20% loss of TCV is about a 10% loss of urea clearance, so the patient gets less dialysis.

Why the other choices don't fit

  • A: Patient size doesn't change the rule.
  • B: More germicide doesn't restore clogged fibers.
  • C: The 80% limit is a discard rule, not a warning.

Source: CMS, ESRD Interpretive Guidance v1.1, Measures Assessment Tool (MAT), V336; Medical Education Institute, Core Curriculum for the Dialysis Technician, 6th ed., "Dialyzer Reprocessing" module (free PDF), "Hollow Fiber Dialyzers and Reuse" and reprocessing steps

Question 45 of 50

Clinical · CCHT-045

Within the first few minutes of treatment, a patient develops hives, shortness of breath, warmth at the fistula and a sense of impending doom. Which complication does this pattern fit?

  • A. Cramping from rapid fluid removal
  • B. Fatigue from a long treatment
  • C. Type A dialyzer reaction
  • D. Dialysis disequilibrium syndrome
Show answer and explanation

Correct answer: C. The guideline describes type A (anaphylactic) dialyzer reactions as usually starting in the first few minutes, with dyspnea, a sense of impending doom, warmth at the fistula site, urticaria and possible collapse. Type B reactions are nonspecific, with chest or back pain 20 to 40 minutes in.

Why the other choices don't fit

  • A: Cramps don't cause hives or a sense of doom.
  • B: Fatigue comes after treatment, not minutes in.
  • D: Disequilibrium causes headache, nausea, restlessness and in severe cases seizures, usually in early sessions.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", "Dialyzer Reactions"

Question 46 of 50

Role Responsibilities · CCHT-046

To recertify the CCHT through continuing education, what does NNCC require over the 3-year certification period?

  • A. 3,000 hours of technician work plus 30 CE contact hours, at least 10 in nephrology
  • B. 1,000 hours of technician work plus 15 CE contact hours in any healthcare topic
  • C. 30 CE contact hours in nephrology, with no minimum number of hours worked
  • D. Passing the CCHT exam again every 3 years, since CE can't be used to renew
Show answer and explanation

Correct answer: A. NNCC requires at least 3,000 hours of dialysis technician work in the 3-year period for either recertification option, and the CE option requires 30 contact hours, at least 10 through nephrology education. You can also recertify by exam within the year before expiration.

Why the other choices don't fit

  • B: Both numbers are lower than NNCC's requirements.
  • C: The 3,000 work hours are required for both options.
  • D: Recertifying by exam is one of two options; CE is the other.

Source: NNCC, Certification Examination Applications handbook (CCHT), "Steps Towards Recertification"; NNCC, CCHT certification page, FAQ

Question 47 of 50

Environment · CCHT-047

A patient's anti-HBs result 1 to 2 months after the hepatitis B vaccine series is 14 mIU/mL. How does CMS guidance interpret this?

  • A. No interpretation is possible without a 'positive' or 'negative' label
  • B. Not immune; repeat the full series
  • C. Infected with hepatitis B
  • D. Immune (10 mIU/mL or higher); retest the patient annually
Show answer and explanation

Correct answer: D. CMS tag V127 says anti-HBs ≥10 mIU/mL means immune, and responding patients are retested annually. A result under 10 means susceptible and calls for revaccination. Results should be reported as a number; 'positive' or 'negative' alone isn't enough.

Why the other choices don't fit

  • A: CMS wants numeric results for exactly this reason.
  • B: Revaccination is for results below 10 mIU/mL.
  • C: Anti-HBs is an antibody from the vaccine response, not a marker of infection.

Source: CMS, ESRD Program Interpretive Guidance Version 1.1 (S&C-09-01), a CCHT core reference, V127

Question 48 of 50

Clinical · CCHT-048

Which of these does the Indian anticoagulation guideline list as a factor that favors clotting of the extracorporeal circuit?

  • A. Low blood flow
  • B. Correct needle position
  • C. A properly primed dialyzer with no trapped air
  • D. Starting the heparin pump on time
Show answer and explanation

Correct answer: A. The guideline lists low blood flow, high hematocrit, high UF rate, access recirculation, transfusions or lipid infusions during treatment, and drip chambers (air exposure, foam and turbulence) as factors that favor clotting. Correct priming, timely heparin and good needle position are the precautions against it.

Why the other choices don't fit

  • B: Correct needle position is listed as a precaution against clotting.
  • C: Good priming without retained air is a precaution.
  • D: Timely heparin start is a precaution, not a risk.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Anticoagulation", "Factors Favoring Clotting of Extracorporeal Circuit" and precautions

Question 49 of 50

Technical · CCHT-049

A reprocessed dialyzer has been rinsed and primed for its next use. According to MEI's reprocessing module, what must you do just before starting treatment?

  • A. Add a small amount of fresh germicide so the dialyzer stays clean during treatment
  • B. Test the circuit for residual germicide and confirm it's at or below the accepted level
  • C. Nothing more, because a full saline prime always flushes out all of the germicide
  • D. Look closely at the priming fluid, since any leftover germicide will be visible
Show answer and explanation

Correct answer: B. MEI says to test the dialysis circuit for residual germicide just before starting treatment and confirm it is at or below the manufacturer's and clinic's accepted levels. Earlier, when the dialyzer comes out of storage, a potency test confirms germicide was present and strong enough, since some germicides such as peracetic acid are clear.

Why the other choices don't fit

  • A: Germicide must be rinsed out before blood contact.
  • C: Germicide can hide in fibers and lines, which is why the test is required.
  • D: Some germicides are clear, so looking can't confirm anything.

Source: Medical Education Institute, Core Curriculum for the Dialysis Technician, 6th ed., "Dialyzer Reprocessing" module (free PDF), "Remove the Germicide" and Table 3

Question 50 of 50

Clinical · CCHT-050

Which change does the Indian guideline list among the preventive steps for a patient who keeps having low blood pressure during dialysis?

  • A. Warmer dialysate, set above 39°C to keep the patient more comfortable
  • B. A large meal during treatment to keep blood sugar and pressure steady
  • C. A higher UF rate so treatment can be shortened by 30 minutes or more
  • D. Cooler dialysate, such as 35.5°C or 0.5°C below the patient's temperature
Show answer and explanation

Correct answer: D. Preventive steps for recurrent intradialytic hypotension in the guideline include cooler dialysate, limiting sodium and fluid intake, keeping the UF rate under 10 mL/kg/h (extending time if needed), reassessing dry weight and avoiding food during or right before the session. Prescription changes come from the nephrologist.

Why the other choices don't fit

  • A: The guideline lists cooler dialysate, not warmer, as the preventive step.
  • B: The guideline says to avoid feeding during or right before dialysis.
  • C: A higher UF rate is a cause of hypotension.

Source: Indian Journal of Nephrology, Indian Hemodialysis Guidelines (2020, Suppl 1), "Complications and Their Management", preventive steps for recurrent intradialytic hypotension

This free CCHT practice test has 50 original, unofficial questions for the Certified Clinical Hemodialysis Technician exam from the Nephrology Nursing Certification Commission (NNCC). The questions follow the four blueprint areas in NNCC's current test specifications. It is not a full-length exam. Pick an answer, then open the explanation. Each one names a source you can check, and there's no signup.

Score yourself by blueprint area

Count your correct answers in each row. The weights come from NNCC's CCHT Test Specifications and CCHT Test Blueprint. We matched this set to those weights as closely as 50 questions allow.

Score yourself by blueprint area
CCHT blueprint areaNNCC weightItems on the 150-question examQuestions in this setQuestion numbers
I. Clinical48–52%71–78251, 3, 6, 8, 9, 12, 14, 16, 17, 20, 22, 24, 25, 27, 29, 31, 34, 35, 37, 39, 42, 43, 45, 48, 50
II. Technical21–25%32–38122, 7, 10, 15, 19, 23, 28, 32, 36, 41, 44, 49
III. Environment13–17%19–2574, 11, 18, 26, 33, 40, 47
IV. Role Responsibilities10–14%15–2065, 13, 21, 30, 38, 46
Total100%15050

Your score here covers these 50 items only. It isn't a CCHT score and doesn't predict a pass. NNCC sets the passing point with an Angoff standard-setting panel, so the real exam measures you against a fixed standard, not against other test takers (NNCC Certification Examination Applications handbook). With 6 to 25 items per area here, treat a weak row as a topic to review, not a measurement.

Clinical is about half the exam. If you missed several Clinical questions, start there. NNCC's specifications also put roughly two-thirds of exam items at the application level, meaning you'll be asked what to do in a situation more often than to recall a definition. Most questions in this set are written the same way.

What the real CCHT exam looks like

What the real CCHT exam looks like
DetailCurrent ruleSource
Who runs itNephrology Nursing Certification Commission (NNCC), with testing partner C-NET (Center for Nursing Education and Testing)NNCC CCHT page
Questions150 multiple-choice. About 25 are unscored pilot questions mixed in with the scored onesNNCC CCHT page; NNCC applications handbook, "Where do these test specifications come from?"
Time3 hoursNNCC CCHT page
Passing scoreA standard score of 95, which NNCC says is reached by answering 74% of questions correctlyNNCC CCHT page
ResultsShown right after a computer-based exam. Candidates who don't pass get a total score and sub scores by test areaNNCC applications handbook, "Examination Results and Notification"
Exam fee$225, which includes a $50 nonrefundable application processing fee. Expedited review is $75; a 90-day testing extension is $125NNCC CCHT page, "Standard Fees"
Permit timingUp to 4 weeks after C-NET receives your application, or 1 to 3 business days with FastTrackNNCC CCHT page, FAQ
RecertificationEvery 3 years. Both options need 3,000 hours of dialysis technician work in the period; the CE option also needs 30 contact hours (at least 10 in nephrology)NNCC applications handbook, "Steps Towards Recertification"; NNCC CCHT page, FAQ
NNCC's own practice exam$30 for 50 questions, available for 90 days, with practice and test modesNNCC CCHT page, "About the Online Practice Exam"

The pace on test day works out to 1.2 minutes per question (180 minutes ÷ 150 questions). To practice at that pace, give yourself 60 minutes for these 50.

Who can sit for the CCHT

Who can sit for the CCHT
RequirementWhat NNCC asks for
EducationHigh school diploma or GED, with a copy submitted. The name must match the application or you need proof of a name change
TrainingA completed hemodialysis technician training program with both classroom instruction and supervised clinical experience, verified by the educator or a certificate
If you're not yet working as a technicianThe number of hands-on clinical hours from training and the facility name, signed by an administrator or manager confirming RN supervision. Observation or shadowing alone doesn't count
If you've worked as a technician in the last 18 monthsYour employer's name and a supervisor's signature. NNCC recommends, but doesn't require, at least 6 months (or 1,000 hours) of clinical experience
If you haven't worked as a technician for 18 months or moreProof of current retraining in both classroom and hands-on care, verified by an RN educator
RegulationsYou must meet the training and experience requirements of the CMS Conditions for Coverage for ESRD facilities and of your state

Source: NNCC CCHT page and the NNCC applications handbook, "CCHT Eligibility Criteria."

CMS rules set the job-side deadline: a newly hired patient care technician must be certified by a state program or a CMS-approved national program, such as the CCHT, within 18 months of hire (CMS ESRD Interpretive Guidance v1.1, tag V695).

Numbers that show up in these questions

These are the specific values the answer explanations use, collected in one place. Most come from the CMS ESRD Interpretive Guidance, which NNCC lists as a core reference. It adopts the AAMI RD52:2004 water and dialysate requirements. On the job, follow your facility's policies, your medical director's protocols and the equipment and test kit manufacturers' instructions. Newer AAMI and ISO standards may differ in places, so when a value conflicts, follow your facility's procedure.

Numbers that show up in these questions
TopicValueSource
Carbon bedsTwo in series, with a sample port after eachCMS tag V192
Empty bed contact timeAt least 5 minutes per bed, 10 minutes total, at maximum flowCMS tag V195
Total chlorine or chloramine after carbonBelow 0.1 mg/L (free chlorine alone: 0.5 mg/L)CMS tags V196 and V192
Chlorine testingStart of each treatment day and before each shift (about every 4 hours with no set shifts); system running at least 15 minutes; test on siteCMS tag V196
First bed breakthroughUp to 72 hours of operation while a bed is replaced, if the second port stays negativeCMS tag V197
Bacteria (product water and dialysate)Action level 50 CFU/mL; maximum below 200 CFU/mLCMS Measures Assessment Tool, V178
EndotoxinAction level 1 EU/mL; maximum below 2 EU/mLCMS Measures Assessment Tool, V180
Dialysate pHChecked with an independent method before every treatmentCMS tag V250
Dialyzer reuseDiscard below 80% of original total cell volumeCMS Measures Assessment Tool, V336
Hemodialysis adequacyspKt/V ≥1.2 or URR ≥65%CMS Measures Assessment Tool, V629
Blood spill disinfectionTuberculocidal disinfectant or 1:100 bleach (300–600 mg/L free chlorine)CMS tags V120 and V122
Alcohol hand rub60–90% alcoholCMS tag V113
Hepatitis B vaccine responseAnti-HBs ≥10 mIU/mL means immuneCMS tag V127

How to get the most out of this set

  1. Answer all 50 before opening any explanation. Note how sure you were on each one.
  2. Score by blueprint area with the table above.
  3. Read every explanation, including the ones you got right. Right answers you guessed are misses waiting to happen.
  4. For each miss, open the cited source and read the section around it. The CMS Interpretive Guidance is free and covers most of the Technical and Environment questions here.
  5. Rework the set a week later. Option order on the real exam won't match this page, so make sure you know why the answer is right instead of remembering where it sat.

CCHT practice test FAQ

How many questions are on the CCHT exam?

150 multiple-choice questions in 3 hours. About 25 of them are unscored pilot questions that NNCC is testing for future use. They look like the others, so answer every question carefully.

What score do you need to pass the CCHT?

A standard score of 95. NNCC says this is reached by answering 74% of the test questions correctly. The cut score comes from an Angoff panel of technicians, so you're measured against a set standard, not graded on a curve.

Are these real CCHT exam questions?

No. Castleport Test Prep wrote every question here from public sources. None are real, recalled or leaked exam items, and the set isn't a simulation of any specific exam form. NNCC states that its exam content is confidential and isn't shared with test prep providers.

What should I study after this practice test?

NNCC's core references are the CMS ESKD Program Interpretive Guidance Version 1.1, Kallenbach's Review of Hemodialysis for Nurses and Dialysis Personnel (9th edition) and the Medical Education Institute's Core Curriculum for the Dialysis Technician (6th edition). NNCC also lists its Water for Dialysis: What You Need to Know (2023) as an additional reference, and offers its own $30 online practice exam. The CMS guidance is free to read, and MEI's dialyzer reprocessing module is free as a PDF.

How long do I have to get certified after I'm hired?

Under CMS rules, a newly hired patient care technician has 18 months from hire to become certified. Until then, the technician must have completed the facility's approved training program before providing care independently.

Is the CCHT the same as the CCHT-A?

No. NNCC describes the CCHT as the entry-level credential. The CCHT-A is an advanced credential for technicians working at an advanced level, such as precepting new technicians, for at least 5 years and 5,000 hours. It's earned only by passing the separate CCHT-A exam.

Sources

Last verified: November 10, 2026. We checked exam format, fees, eligibility, passing score and recertification rules against NNCC's CCHT page and applications handbook, blueprint weights against the 2021 test specifications, and every answer against the source cited with it.

By the Castleport Test Prep Editorial Team.

Castleport Test Prep is an independent exam prep publisher. We are not affiliated with, endorsed by, or approved by the Nephrology Nursing Certification Commission (NNCC). CCHT and other exam and credential names are used only to identify their subjects; trademarks belong to their respective owners. These practice questions are original and unofficial and are for study only. They aren't clinical guidance; follow your facility's policies and the orders of the care team.

No qualified dialysis clinician review of this version is documented.